View AB207_8938503.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

luxeon 3030 2d and luxeon 3030 hv assembly and handling information introduction this application brief addresses the recommended assembly and handling guidelines for luxeon 3030 2d and luxeon 3030 hv emitters. these emitters deliver high efcacy and quality of light for distributed light source applications in a compact 3.0mm x 3.0mm package. proper assembly, handling, and thermal management, as outlined in this application brief, ensure high optical output and reliability of these emitters. scope the assembly and handling guidelines in this application brief apply to the following luxeon products: products luxeon 3030 2d luxeon 3030 hv in the remainder of this document the term luxeon emitter refers to any product in the luxeon series listed above. illumination AB207 luxeon 3030 2d and luxeon 3030 hv application brief ?2016 lumileds holding b.v. all rights reserved.
AB207 luxeon 3030 2d and luxeon 3030 hv application brief 20160303 ?2016 lumileds holding b.v. all rights reserved. 2 table of contents introduction 1 scope 1 1 component 3 1.1 description ......................................................................... 3 1.2 optical center ....................................................................... 3 1.3 handling precautions ................................................................. 3 1.4 cleaning ............................................................................ 3 1.5 electrical isolation .................................................................... 4 1.6 mechanical files ...................................................................... 4 2 pcb design guidelines for the luxeon emitter 4 2.1 pcb footprint and land pattern ....................................................... 4 2.2 surface finishing ..................................................................... 4 2.3 minimum spacing .................................................................... 4 3 thermal management 5 4 thermal measurement guidelines 7 5 assembly process guidelines 8 5.1 stencil design ........................................................................ 8 5.2 solder paste ......................................................................... 8 5.3 solder refow profle .................................................................. 8 5.4 pick and place ....................................................................... 8 5.5 electrostatic discharge protection ...................................................... 9 5.6 jedec moisture sensitivity ............................................................. 9 6 packaging considerations chemical compatibility 9
AB207 luxeon 3030 2d and luxeon 3030 hv application brief 20160303 ?2016 lumileds holding b.v. all rights reserved. 3 1. component 1.1 description the luxeon emitter (figure 1) is an emc (epoxy molding compound) molded, no-lead, surface mount package consisting of an anode and a cathode. a small circle on the corner of the package marks the cathode side of the emitter package. majority of the heat is being dissipated through the larger pad (cathode). the luxeon emitter does not include any transient voltage suppressor (tvs) chip to protect the emitter against electrostatic discharges (esd) appropriate precautions should therefore be taken when handling this device (see section 5.5). the inspectable solder joint feature (figure 1) to check the presence of solder fllet for quality monitoring is not used. 1.2 optical center the optical center coincides with the mechanical center of the luxeon emitter. optical rayset data for the luxeon emitter are available at lumileds com. 1.3 handling precautions the luxeon emitter is designed to maximize light output and reliability. however, improper handling of the device may damage the silicone encapsulation and afect the overall performance and reliability. in order to minimize the risk of damage to the silicone encapsulation during handling, the luxeon emitter should only be picked up from the side of the package (figure 2). 1.4 cleaning the luxeon emitter should not be exposed to dust and debris. excessive dust and debris may cause a drastic decrease in optical output. in the event that a luxeon emitter requires cleaning, frst try a gentle swabbing using a lint-free swab. if needed, a lint-free swab and isopropyl alcohol (ipa) can be used to gently remove dirt from the silicone coating. do not use other solvents as they may adversely react with the package of the luxeon emitter. for more information regarding chemical compatibility, see section 6. figure 1. package rendering of the luxeon 3030 2d emitter. figure 2. correct handling (left) and incorrect handling (right) of luxeon emitters.
AB207 luxeon 3030 2d and luxeon 3030 hv application brief 20160303 ?2016 lumileds holding b.v. all rights reserved. 4 1.5 electrical isolation the luxeon emitter contains two electrode pads on the package. it is important to keep sufcient distance between the luxeon emitter package and any other objects or neighboring luxeon emitters to prevent any accidental shorts. in order to avoid any electrical shocks, fashover and/or damage to the luxeon emitter, each design needs to comply with the appropriate standards of safety and isolation distances, known as clearance and creepage distances, respectively (e.g. iec60950, clause 2.10.4). 1.6 mechanical files mechanical drawings for the luxeon emitter are available at lumileds com. 2. pcb design guidelines for the luxeon emitter the luxeon emitter is designed to be soldered onto a printed circuit board (pcb). to ensure optimal operation, the pcb should be designed to minimize the overall thermal resistance between the led package and the heat sink. 2.1 pcb footprint and land pattern the recommended pcb footprint design for the luxeon emitter is shown in figure 3. in order to ensure proper heat dissipation from the emitter electrodes to the pcb, it is best to extend the top copper layer of the pcb beyond the perimeter of the luxeon emitter by at least 4mm (see section 3). 2.2 surface finishing lumileds recommends using a high temperature organic solderability preservative (osp) or electroless nickel immersion gold (enig) plating on the exposed copper pads. 2.3 minimum spacing lumileds recommends a minimum edge to edge spacing between luxeon emitters of 0.5mm. placing multiple luxeon emitters too close to each other may adversely impact the ability of the pcb to dissipate the heat from the emitters.
AB207 luxeon 3030 2d and luxeon 3030 hv application brief 20160303 ?2016 lumileds holding b.v. all rights reserved. 5 solder mask stencil top copper 1.33 2.30 2.20 2.30 0.58 0.48 1.53 0.05 0.69 package geometric center 1.15 0.13 2.10 figure 3. recommended pcb footprint design for the luxeon emitter (top). in order to ensure proper heat dissipation from the package electrodes to the pcb, it is best to extend the top copper layer of the pcb several millimeters beyond the package of the luxeon emitter. see section 3 for more information on the copper layout. all dimensions are in mm. bottom picture shows the actual fr4 pcb footprint layout. 3. thermal management the overall thermal resistance between a luxeon emitter and the heat sink is strongly afected by the design and material of the pcb on which the emitter is soldered. metal core pcbs have been historically used in the led industry for their low thermal resistance and rigidity. however, mcpcbs may not always ofer the most economical solution. multi-layer epoxy fr4 pcbs are commonly used in the electronics industry and can, if properly designed, yield an appropriate low-cost solution for various led applications. lumileds investigated the thermal performance of luxeon emitters on a 1.0mm thick fr4 pcb with a top copper plating of 35m (single sided copper layer pcb). in order to quantify the impact of the top copper metallization design layout on the overall thermal resistance between junction and heat sink, two designs with varying copper trace layout around the anode and cathode were evaluated as shown in table 1. the two designs are: a. a C minimum top copper corresponds to copper trace which extends beyond the outline of the luxeon emitter package by 0.25mm which corresponds to half of the minimum recommended package to package spacing of 0.5mm. this confguration is representative of worst case condition for application where multiple leds are placed in close proximity to each other. b. b C maximize top copper around the cathode as much as possible. this is the ideal layout for fr4 pcb since the primary heat fow of the luxeon emitter is through the cathode pad as described in section 1.1. as general guidelines, increasing the top copper thickness and increasing the copper area around the cathode will reduce the fr4 board thermal resistance. adding a bottom copper layer to the fr4 (double sided copper clad pcb) does not reduce the fr4 thermal resistance since the fr4 material itself is a poor thermal conductor.
AB207 luxeon 3030 2d and luxeon 3030 hv application brief 20160303 ?2016 lumileds holding b.v. all rights reserved. 6 table 1. typical thermal resistance values for fr4 pcbs with varying top copper trace pattern (solid red area). design b yield s the lowest board thermal resistance. design typical r j- bottom pcb [k/w] typical r j-s [k/w] a (mimimum copper pattern, 0.25mm around package outline) 74 18 b (maximize copper around cathode pad) 32 12
AB207 luxeon 3030 2d and luxeon 3030 hv application brief 20160303 ?2016 lumileds holding b.v. all rights reserved. 7 figure 4. the recommended temperature measurement point ts is located on the cathode copper layer of the pcb, closest to the package. the picture above shows where to place the welding tip of the tc wire prior to dispensing any thermal conductive epoxy to secure the tc wire. tip of tc wire secured with epoxy figure 5. photo showing actual placement of tc wire secured with thermal conductive epoxy. the thermal epoxy volume should be kept to minimum as shown. 4. thermal measurement guidelines the typical thermal resistance r j-case between the junction and the solder pads of the luxeon emitter is provided in the datasheet. with this information, the junction temperature t j fdehghwhuplhgdffrugljwrwkhiroorljhtxdwlr t j = t thermal pad + r j-thermal pad ? p electrical tr t case is the temperature at the bottom of the solder pads of the luxeon emitter and p electrical is the electrical srhujrljlwrwkhhplwwhuCwslfdodssolfdwlrvlwpdehglfxowwkrxjkwrphdvxuhwkhwhpshudwxuh7 case directly. therefore, a practical way to determine the junction temperature of the luxeon emitter is by measuring the temperature t s of a predetermined sensor pad on the pcb with a thermocouple. the recommended location of the sensor pad is right next to the cathode of the luxeon emitter on the pcb, as shown in figure 4 and figure 5. to ensure accurate reading, the thermocouple (tc) tip must make direct contact to the copper of the pcb onto which the luxeon emitter cathode pad is soldered, i.e. any solder mask or other masking layer must eh4uvwuhprhgehiruhprxwljwkhwkhuprfrxsohrwrwkh37khwlsriwkh7luhkhuhwrglvvlploduphwdov are welded should be placed as close as possible to the luxeon emitter package on the exposed cathode copper layer as shown in figure 4. the thermal resistance r j-s between the sensor pad and the luxeon emitter junction was hshulphwdooghwhuplhgr)53viruwkhwrglhuhwghvl jvvhh7deoh7khmxfwlrwhpshudwxuhfdwkh be calculated as follows: t j = t s + r j-s ? p electrical it is recommended to secure the tip of tc wire to the exposed copper area with a good thermal conductive epoxy such as artic silver? thermal adhesive. note that the artic silver? epoxy is not formulated to conduct electricity. during dispensing rihsrdrlg5rrgljwkh7luhlwkwrrpxfkhsrexwvxflhwhrxjkwrvhfxuhwkh7luhiruphdvxuhphw putting more epoxy than needed may change the thermal behavior of the surrounding area.
AB207 luxeon 3030 2d and luxeon 3030 hv application brief 20160303 ?2016 lumileds holding b.v. all rights reserved. 8 5. assembly process guidelines 5.1 stencil design the recommended solder stencil thickness is 125m or 5mils. 5.2 solder paste lumileds recommends lead-free solder for the luxeon emitter such as sac 305 solder paste from alpha metals (sac305- cvp390-m20 type 3). however, since application environments vary widely, lumileds recommends that customers perform their own solder paste evaluation in order to ensure it is suitable for the targeted application. 5.3 solder refow profle the luxeon emitter is compatible with standard surface-mount and lead-free refow technologies. this greatly simplifes the manufacturing process by eliminating the need for adhesives and epoxies. the refow step itself is the most critical step in the refow soldering process and occurs when the boards move through the oven and the solder paste melts, forming the solder joints. to form good solder joints, the time and temperature profle throughout the refow process must be well maintained. a temperature profle consists of three primary phases: 1. preheat: the board enters the refow oven and is warmed up to a temperature lower than the melting point of the solder alloy. 2. refow: the board is heated to a peak temperature above the melting point of the solder, but below the temperature that would damage the components or the board. 3. cool down: the board is cooled down rapidly, allowing the solder to freeze, before the board exits the oven. as a point of reference, the melting temperature for sac 305 is 217c, and the minimum peak refow temperature is 235c. 5.4 pick and place the luxeon emitter is packaged and shipped in tape-and-reel which is compatible with standard automated pick-and- place equipment to ensure the best placement accuracy. note that pick and place nozzles are customer specifc and are typically machined to ft specifc pick and place tools. lumileds advises customer to take the following general pick and place guidelines into account: a. the nozzle tip should be clean and free of any particles since they may interact with the top surface of the silicone encapsulation of the luxeon emitter package. b. during setup and the frst initial production runs, it is a good practice to inspect the top surface of the luxeon emitters under a microscope to ensure that the emitters are not accidentally damaged by the pick and place nozzle.
AB207 luxeon 3030 2d and luxeon 3030 hv application brief 20160303 ?2016 lumileds holding b.v. all rights reserved. 9 5.5 electrostatic discharge protection the luxeon emitter does not include any transient voltage suppressor (tvs) chip to protect against electrostatic discharges (esd). therefore, lumileds recommends observing the following precautions when handling the luxeon emitter: during manual handling always use a conductive wrist band or ankle straps when positioned on a grounded conductive mat. all equipment, machinery, work tables, and storage racks that may get in contact with the luxeon emitter should be properly grounded. use an ion blower to neutralize the static discharge that may build up on the surface and lens of the plastic housing of the luxeon emitter during storage and handling. luxeon emitters which are damaged by esd may not light up at low currents and/or may exhibit abnormal performance characteristics such as a high reverse leakage current, and a low forward voltage (leaky diode). it is also important to take note that esd can also cause latent failure, i.e. failure or symptoms as described above may not show up immediately but until after use. hence continuous esd protection is needed during assembly. 5.6 jedec moisture sensitivity luxeon 3030 2d msl (jedec moisture sensitivity level) is rated as level 3. proper storage, handling and/or baking must be adhered to prevent damage to the luxeon emitter during refow. table 2. msl level floor life soak requirements standard time conditions time conditions 3 168 hours 30c / 60% rh (relative humidity) 192 +5 / -0 hours 30c / 60% rh table 3. storage and baking conditions. note that if any of the temperature, relative humidity, humidity indicator card or the period is not met, baking is required. for more information, see ipc/jedec j-std-033c operation packing ba g status temperature relative humidity (rh) humidit y indicator card period storage as received 30c (non-condensing atmospheric environment) 90% n/a within 1 year of shipment date storage after opening bag 30c 60% if 10% color spot is no longer blue 168 hours baking (drying) n/a 60 5c 5% n/a 24 hours 6. packaging considerations chemical compatibility the luxeon emitter package contains a silicone overcoat to protect the led chip and extract the maximum amount of light. as with most silicones used in led optics, care must be taken to prevent any incompatible chemicals from directly or indirectly reacting with the silicone. the silicone overcoat used in the luxeon emitter is gas permeable. consequently, oxygen and volatile organic compound (voc) gas molecules can difuse into the silicone overcoat. vocs may originate from adhesives, solder fuxes, conformal coating materials, potting materials and even some of the inks that are used to print the pcbs.
AB207 luxeon 3030 2d and luxeon 3030 hv application brief 20160303 ?2016 lumileds holding b.v. all rights reserved. 10 some vocs and chemicals react with silicone and produce discoloration and surface damage. other vocs do not chemically react with the silicone material directly but difuse into the silicone and oxidize during the presence of heat or light. regardless of the physical mechanism, both cases may afect the total led light output. since silicone permeability increases with temperature, more vocs may difuse into and/or evaporate out from the silicone. careful consideration must be given to whether luxeon emitters are enclosed in an air tight environment or not. in an air tight environment, some vocs that were introduced during assembly may permeate and remain in the silicone. under heat and blue light, vocs captured inside the silicone may partially oxidize and create a silicone discoloration, particularly on the surface of the led where the fux energy is the highest. in an air rich or open air environment, vocs have a chance to leave the area (driven by the normal air fow). transferring the devices which were discolored in the enclosed environment back to open air may allow the oxidized vocs to difuse out of the silicone and may restore the original optical properties of the led. determining suitable threshold limits for the presence of vocs is very difcult since these limits depend on the type of enclosure used to house the leds and the operating temperatures. also, some vocs can photo-degrade over time. table 4 provides a list of commonly used chemicals that should be avoided as they may react with the silicone material. note that lumileds does not warrant that this list is exhaustive since it is impossible to determine all chemicals that may afect led performance. the chemicals in table 4 are typically not directly used in the fnal products that are built around luxeon emitters. however, some of these chemicals may be used in intermediate manufacturing steps (e.g. cleaning agents). consequently, trace amounts of these chemicals may remain on (sub) components, such heat sinks. lumileds, therefore, recommends the following precautions when designing your application: C when designing secondary lenses to be used over an led, provide a sufciently large air-pocket and allow for ventilation of this air away from the immediate vicinity of the led. C use mechanical means of attaching lenses and circuit boards as much as possible. when using adhesives, potting compounds and coatings, carefully analyze its material composition and do thorough testing of the entire fxture under high temperature over life (htol) conditions.
AB207 luxeon 3030 2d and luxeon 3030 hv application brief 20160303 ?2016 lumileds holding b.v. all rights reserved. 11 table 4. list of commonly used chemicals that will damage the silicone of the luxeon emitter. avoid using any of these chemicals in the housing that contains the led package. chemical name normally used as hydrochloric acid acid sulfuric acid acid nitric acid acid acetic acid acid sodium hydroxide alkali potassium hydroxide alkali ammonia alkali mek (methyl ethyl ketone) solvent mibk (methyl isobutyl ketone) solvent toluene solvent xylene solvent benzene solvent gasoline solvent mineral spirits solvent dichloromethane solvent tetracholorometane solvent castor oil oil lard oil linseed oil oil petroleum oil silicone oil oil halogenated hydrocarbons (containing f, cl, br elements) misc rosin fux solder fux acrylic tape adhesive rohs compliant no. e352519
?2016 lumileds holding b.v. all rights reserved. luxeon is a registered trademark of the lumileds holding b.v. in the united states and other countries. lumileds com about lumileds lumileds is the global leader in light engine technology. the company develops, manufactures and distributes groundbreaking leds and automotive lighting products that shatter the status quo and help customers gain and maintain a competitive edge. with a rich history of industry frsts, lumileds is uniquely positioned to deliver lighting advancements well into the future by maintaining an unwavering focus on quality, innovation and reliability. to learn more about our portfolio of light engines, visit lumileds.com . neither lumileds holding b.v. nor its afliates shall be liable for any kind of loss of data or any other damages, direct, indirect or consequential, resulting from the use of the provided information and data. although lumileds holding b.v. and/or its afliates have attempted to provide the most accurate information and data, the materials and services information and data are provided as is, and neither lumileds holding b.v. nor its afliates warrants or guarantees the contents and correctness of the provided information and data. lumileds holding b.v. and its afliates reserve the right to make changes without notice. you as user agree to this disclaimer and user agreement with the download or use of the provided materials, information and data. AB207 luxeon 3030 2d and luxeon 3030 hv application brief 20160303

▲Up To Search▲

Price & Availability of AB207

	To Download AB207 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .